Electronic Resources, Boardman is Turkish MANUAL subject " printed circuit board maker * * * board make use of manual board maker * The Boardman * guide * course * PCB PCB editor program * "tagged with
A study pcb printed circuit board maker and drawing program, containing detailed information about the use of Turkish "Board Maker Turkish User's Guide"
A lot of people's first eye pain with me I made my first PCB drawing Boardman is rather I tried to prepare and labor thanks to the person dealing with a very old program electronic
Boardman's (UN), printed circuit drawing is a software used in the preparation of electrical and electronic circuit diagrams.
Electronic circuit board bread ( try the board ), perforated pertinaks , copper plaquetted installation on vehicles like. Long lasting and circuits used for the smooth operation produced the desired soldered onto copper plates.
access roads will be built on the circuit made of copper copper plaquetted. One or two scratches on the surface of the thin copper plate covered with printed circuit plaquetted after drying, melting acid (1 part Perhydrolysis three parts hydrochloric acid mixture ) into atyıl. Solvents dissolve in acid copper property located in the unpainted part on the plate. After the melting process mechanical powder paint lines on the printed circuit board, land or deleted with fine sandpaper. Circuit is produced by making the soldering After drilling the holes required for the installation of circuit elements with 1-2 mm diameter drill bit.
Required to remove the printed circuit board printed circuit made on the plaque can be hand-drawn diagram software can also be used.
Boardmaker software is also one of the printed circuit extraction. Boardman software may be sufficient for more amateur work. Professional (mass production) for studies often Orcad, Protel, Quickrout to, Multisim, Ultiboard etc . such software are used. Computer Boardman is at least 640 KB of RAM memory to run the software you need a computer. UN because it is the lowest-featured single disk (eg 80286 processor) even run on the computer.
Software features : Single-disk is a software Boardman (UN) bilgisayaryn the floppy drive (A or B) was inserted directly executable. If the software is a bit faster than desired operation of the hard disk (C or D) kind with UN contents of a floppy disk after opening a folder named executable is copied here.
Boardman is 'the preparation of a printed circuit diagram PCB Editor ( Printed Circuit Board Editor ), printed circuit board editor) electrical or electronic circuit Schematic where şemalaryn scratching Editor ( schematic editor ), symbols, and the production of material sheath shape and kullanyl the Library Editor ( library, icon editor ) has sections.
XI. Kill: command çalıştırılmasııl to the active pad deleted. First to be deleted before the pad is selected. In the kill command line çalıştırılmasııl message, Please confirm. TIPEM (i) es or (N) from the user to delete the file, it is desirable to him. then pressing the delete operation is performed. Kill can be performed by pressing the K key on the keyboard.
Pad placement: PCB Editor is executed at the UN. Pad run the Add menu. Iere yerleşeceş the cursor pad and press the Enter key on the keyboard be in the drawing area. This is a pad made, appears in the drawing area. Generated pad is pressed the Esc key on the keyboard to remove the selected state.
Changing the way Pad: The pad is placed in the design area activated yet. Then run the Shape command from the Option menu. Çalıştırılmasııl this command to display 14 different pad appears.Cursor is positioned over the desired pad and press Enter on the keyboard.
Changing Pad dimensions: Add / a pad Pad command is added to the design. Later Track and pad sizes Config menu command is executed. On the screen, User configuration options [track and pad sizes] in mm widths seçeneş Pad window appears. Outside (the pad's outer diameter) and the inside (the pad inner diameter) values, the de l'were numbered from 16'ı. Pad values, the measure of (+) and (-) can deşiştiril using the buttons. Press the Esc key twice to exit the window on the screen.
Positioned in the selected design case when a pad Width Option menu
command in the message line is executed, the width Please enter a number (1-16) message is received. Keyboarding
entering a number from 1 to 16 using pressed Enter.
command in the message line is executed, the width Please enter a number (1-16) message is received. Keyboarding
entering a number from 1 to 16 using pressed Enter.
Adding text to the design: Text command from the Add menu is selected. Position the cursor in the message line and press [return] received the message. Once this message is brought to anywhere in the cursor design and printed Enter. This time the screen's lower left corner in the line editor ıazı Editing text on the display. from the cursor location beklediş Turkish characters (C, G, S, O, y) without the use of written text. Let's write the text Ornes Ali Ozdemir. After writing, the keyboard Enter or press the left mouse button. This text from the keypad to secure the Esc key, then the design of the mouse button is pressed sachet.
Changing the color of the icon: the command to run the Config menu selection Laie deşiştir the color of the icon placed in the PCB Editor design. Oken in line in the window to display the screen shrugged Upper (right) sign is moved to the left or right oklarııl. brought the cursor to the desired color after the Enter key is pressed the Esc key is pressed twice. The observed changes in the design of the jacket color.
All Boardman Guide: Boardmaker_kilavuz_turkce.r the alternative link2
